BLOG
Can you revive an over-discharged 18650? What the cut-off voltage means
Short answer. In most cases, do not. Every data sheet sets a discharge cut-off voltage: 2.5 V for the Samsung 30Q, 2.65 V for the Samsung 35E, 2.0 V for the Sony VTC6. A cell that has sat below its cut-off can be damaged inside even if it takes a charge. Recycle it. A protected cell that reads 0 V is a different case: its circuit has usually switched off, and a charger resets it.
What the cut-off voltage means
The cut-off is where the data sheet's capacity test ends, and it is the lowest voltage the cell should reach under load. A device, a BMS or a protection circuit should stop the discharge at or above it. Voltage recovers when the load comes off, so a cell that reached 2.5 V under load reads higher a few minutes later. A cell that rests below its cut-off has gone further.
What happens below it
At very low voltage the copper foil that carries current for the negative electrode can begin to dissolve. The dissolved copper can then deposit elsewhere inside the cell and form a path between the electrodes: an internal short circuit. A 2016 study in Scientific Reports that forced large-format lithium-ion cells far past empty found copper deposits causing internal short circuits. The damage does not show from outside, and a cell can take a charge with it.
Flat cell or switched-off circuit?
| WHAT YOU MEASURE | WHAT IT USUALLY MEANS | WHAT TO DO |
|---|---|---|
| A protected cell reads 0 V | The protection circuit has switched off | Put it on a charger, which resets the circuit |
| An unprotected cell rests at or above its cut-off | Empty, not over-discharged | Charge it soon |
| An unprotected cell rests below its cut-off | Over-discharged | Recycle it |
| Any cell that has sat flat for weeks | Deeply over-discharged | Recycle it |
If a protected cell does not come back on a charger, or was left flat for a long time, treat it as over-discharged.
Chargers that revive cells
Some chargers start reviving a low cell without being asked: XTAR lists 0 V activation for the VC4 and the VC8. That brings the voltage back. It cannot show whether the cell was damaged while it was flat. Measure a doubtful cell with a meter before it goes into a charger.
Do not jump-start a cell
Wiring a flat cell to a full one, or forcing current into it from a power supply, sends an uncontrolled current into a cell that may already be damaged. Do not do it.
How to avoid over-discharge
- Recharge cells soon after a device runs flat, and take them out of devices that draw current while switched off.
- Store cells partly charged and check them from time to time. The Samsung 30Q data sheet's storage figures assume about 50% charge.
- Give every pack a BMS with a low-voltage cut-off.
- Use protected cells in single-cell devices that have no cut-off of their own.


Common questions
Can I recharge an 18650 that reads 0 volts?
A protected cell at 0 V has usually switched itself off, and a charger resets it. An unprotected cell at 0 V is deeply over-discharged: recycle it.
What is the lowest safe voltage for an 18650?
The discharge cut-off on its data sheet: 2.5 V for the Samsung 30Q, 2.65 V for the Samsung 35E and 2.0 V for the Sony VTC6. That is a figure under load. Stopping earlier is easier on the cell.
How do I dispose of an over-discharged battery?
Cover the terminals with tape or put the cell in its own case, and take it to a battery recycling point. See how to dispose of and recycle 18650 batteries.
Sources
- Samsung INR18650-35E, Samsung INR18650-30Q, Molicel INR-21700-P50B and Sony US18650VTC6 data sheets, linked from the product pages and the data sheet library.
- Guo, Lu, Ouyang and Feng, Mechanism of the entire overdischarge process and overdischarge-induced internal short circuit in lithium-ion batteries, Scientific Reports 6, 30248 (2016).
- XTAR's 0 V activation is a listing figure from the VC4 and VC8 product pages.
MORE FROM THE BLOG
Keep reading

Protected vs unprotected 18650 batteries: which do you need?
A protected 18650 adds a small circuit that cuts off on over-charge, over-discharge and short circuit. When to use protected or bare cells.

High-drain vs high-capacity cells: how to choose
High-drain cells are built for current, high-capacity cells for energy. Five data sheets side by side, and how to tell which type your device needs.

How to charge 18650 and 21700 batteries
Charge lithium-ion 18650 and 21700 cells to 4.2 V on a lithium-ion charger, at the data-sheet current and temperature. Figures for two cells.